Benefisiasi Bijih Kromit Daerah Paludda Dengan Metode Konsentrasi Gravitasi

Authors

  • Suriyanto Bakri Program Studi Teknik Pertambangan Fakuktas Teknologi Industri Universitas Muslim Indonesia
  • Mohammad Iqbal
  • Sitti Ratmi Nurhawaisyah
  • Muhammad Idris Juradi
  • Hasbi Bakri

DOI:

https://doi.org/10.31315/jmept.v3i2.7309

Keywords:

Bijih Kromit, Benefisiasi, Meja goyang, Paludda

Abstract

Daerah Palludda Barru terdapat bijih kromit dengan kadar rendah atau belum bisa dimanfaatkan lebih lanjut. Metode yang cocok untuk bijih kromit adalah metode konsentrasi gravitasi dengan meja goyang. Penelitian dilakukan dengan tujuan untuk mengetahui besar peningkatan kadar dan perolehan bijih kromit asal Palludda Barru menggunakan meja goyang dengan menvariasikan sudut kemiringan. Hasil penelitian didapatkan kemiringan optimum pada sudut 10° dengan kadar 35,89% dan recovery 59,06%.

References

Abubakre O dkk, (2007). Characterization and beneficiation of chromite ore using magnetic separation process. Journal of Minerals & Materials Characterization & Engineering, volume 6 No.2 hal 143 -150.

Aslan N dan Kaya H, (2009). Beneficiation of chromite concentration waste by multi-gravity separator and high intensity induced roll magnetic separator. The Arabian Journal for Science and Engineering, volume 34 No. 2B hal 285 – 297.

Ernowo dan Oktaviani P, (2010). Review of chromite deposits of Indonesia. Buletin Sumber Daya Geologi.

Kementerian ESDM, (2009). UU No 4 Tahun 2009 Mineral dan Batubara.

Kelly, dkk, 1982, Introduction Mineral

Processing, John Wiley & Sons, Canada, 199.

Kohirozi, N., dkk, 2014, Perhitungan Pengaruh Kemiringan dan Debit Air Pada Pemakaian Shaking Table Dalam Pengolahan Bijih Timah Low Grade Di Pos Pam Pengarem PT Timah (Persero) Tbk. Bina Tambang, 1(1), 1-6.

Maharani, S., dkk, 2020, Pengaruh

kemiringan Shaking Table terhadap kadar dan recovery cassiterite. Jurnal Pertambangan, 4(2), 108-113.

LIPI, 2015. X-Ray Fluorescence. Lipi.go.id, diakses November 2020.

Pariser, G. C. 2013. Ontario’s Ring of Fire: Unlocking Potential and Creating Opportunity. PDAC Convention: Heinz H. Pariser Alloy Metals and Steel Market Research. Toronto.

Purawiardi R, (2008). Karakteristik bijih kromit Barru Sulawesi Selatan. Jurnal Riset Geologi dan Pertambangan, jilid 18 No.1 hal 1 - 13, LIPI Serpong.

Rowe J, (2016). Stainless steel in figures. International Stainless Steel Forum (ISSF), Brussels.

Rumbino, Y., & Banunaek, N, 2021, Pengaruh Variabel Meja Goyang (Shaking Table) untuk Memisahkan Mineral Mangan dari Mineral Pengotor. Jurnal Teknologi, 15(1), 59-62.

Seifelnasr, A., Tammam, T. and Abouzeid, A., 2012. Gravity concentration of Sudanese chromite ore using laboratory shaking table, Physicochemical problem of mineral processing, 48(1), Hal. 271-280

Subandrio dkk, (2017). Optimasi pengolahan bijih kromit secara gravity dengan meja goyang. Jurnal Petro, volume 6 No.2, Jakarta.

Supriadidjaja A dan Hartanto P, (2012). Peningkatan kadar kromit Barru – Sulawesi Selatan. Jurnal teknologi mineral dan batubara, volume 8 No.3: 132 – 140, Bandung.

Triparthy S. Kumar, Singh, V. dan Ramamurthy, Y., 2012.

Improvement in Cr : Fe ratio of Indian chromite ore

for ferrochrome production, International Journal of

Mining Engineering and Mineral Processing, Vol.1(3), Hal. 101-106

Downloads

Published

2023-02-10

Issue

Vol 3, No 2 (February 2023)

Section

Articles

License

Authors who publish in Journal of Metallurgical Engineering and Processing Technology agree to the following terms:

  1. Authors who publish articles in this journal agree to the following terms:

    1. Copyright remains with the author and gives rights to the Journal of Metallurgical Engineering and Processing Technology as the priority to publish the article with an Creative Commons Atribusi 4.0 Internasional License, which allows the article to be shared with acknowledgment of the author of the article and this journal as the place of publication.
    2. Authors can distribute the publication of their articles on a non-exclusive basis (for example: on university repositories or books) with notification or acknowledgment of publication in the journal Option
    3. Authors are allowed to post their work online (for example: on personal websites or in university repositories) before and after the submission process (see The Effect of Open Access)

    Journal of Metallurgical Engineering and Processing Technology is licensed under a Creative Commons Atribusi 4.0 Internasional License.