Experimental Analysis of Magnetic Particle Inspection on S355J2 Steel Weld Joints

Muhammad Avicena Apriliansyah

Abstract


NDT (Non-Destructive Test) is a form of testing carried out on materials or objects without causing permanent damage to these materials or objects. This study aims to determine the NDT Magnetic Particle Inspection testing process that is carried out and find out the results of the inspection of S355 J2 steel specimens with the NDT Magnetic Particle Inspection test method as the basis for determining the GMAW Welder Qualification. Welding of S355 J2 Steel is performed by a certified welder using GMAW welding using a single V-butt joint at an angle of 30 degrees. NDT Visual Test and Magnetic Particle Inspection are carried out during material testing. Data & output shows welder PT. INKA qualified with the standards set by the company, namely AWS D1.1 and ASTME E 709. So the Welder can be allowed to work on a Project because it is considered to have met the required Welder qualification standards.


Keywords


MPI, S355 J2, WPQR, Welding GMAW, Physical metallurgy

Full Text:

PDF

References


Ahmad Abi Sodik1 , Nely Ana Mufarida2 , Kosjoko3. 2019. Pengaruh Penerapan WPS (Welding Procedure Specification) Al 6005 Tipe Butt Joint Terhadap Kekuatan Sambungan Las Al 6061. Jember: Universitas Muhammadiyah jember

Alfian Wahyu Prasetya, 2017 " Pengaruh Debit Gas Pelindung Dan Tegangan Listrik Terhadap Tingkat Kekerasan Dan Struktur Mikro Sambungan Las Gmaw Pada Baja Karbon Sedang Ems-45 " Semarang , Universitas Negeri Semarang.

Alip, M. 1989. Teori dan Praktik Las. Yogyakarta: IKIP Yogyakarta

Amalia, Y., & Rahmatillah, S. (2022). Analisis Sambungan Las Baja S355 J2 Sebagai Penyusun Welding Procedure Specification di PT Industri Kereta Api. JUSTER : Jurnal Sains Dan Terapan, 1(2), 1–6.

A. Ibrahim, S. A. Mohamat, A. Amir, and A. Ghalib, “The Effect of Gas Metal Arc Welding (GMAW) processes on different welding parameters,” Procedia Eng., vol. 41, pp. 1502–1506, 2012.

B. Mvola and P. Kah, “Effects of shielding gas control: welded joint properties in GMAW process optimization,” Int. J. Adv. Manuf. Technol., vol. 88, no. 9–12, pp. 2369– 2387, 2017.

Cecep Slamet Abadi1, Rosidi, Idrus Assagaf . 2019 . " Analisa Kekuatan Welding Repair Baja Aisi 420 Dengan Metoda Gmaw " Politeknologi Vol. 18 No. 3. jakarta. Politeknik Negeri Jakarta

E. Karadeniz, U. Ozsarac, C. Yildiz. 2007, The effect of process parameters on penetration in gas metal arc welding processes. Materials & design, Vol. 28, no. 2: 649-656.

Kholis, Ikhsan. 2012. Kualifikasi Welding Procedure Specification (WPS) dan Juru Las (Welder) Berdasarkan ASME Section IX di Industri Migas. Forum Teknologi, 2(3), 16- 25.

Mujiyanto, Tantok. 2008. Analisis Hasil Pengelasan GMAW Dengan Jenis Ekeltroda ER70S6 di PT INKA Madiun. Madiun: Universitas Merdeka Madiun

Patil, NR. 2008. Non Destructive Testing (NDT) Advantages and limitations. SRES College of Engineering, Kopargaon, Maharastha, 423-603

Rahmatika, Amelia, dkk. 2021. Pengujian Merusak Pada Kualifikasi Prosedur Las Plat Baja Karbon SA-36 dengan Proses Pengelasan SMAW Berdasarkan Standar ASME Section IX. Jurnal Vokasi Teknologi Industri, 3(1), 24-30.

Sri, Widharto. 2013. Welding Inspection. Mitra Wacana Media. Jakarta.

Suwahyo. 2011. Mengelas Dengan Proses Las Busur Listrik Manual. Yogyakarta: PT. Pustaka Insan Madani

Wahyudi, Muhammad Thoriq, dkk. 2015. Modul Praktek Kualifikasi Las. Surabaya: Politeknik Perkapalan Negeri Surabaya.




DOI: https://doi.org/10.31315/jmept.v4i1.7813

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Journal of Metallurgical Engineering and Processing Technology

Journal of Metallurgical Engineering and Processing Technology indexed by:

 




Journal of Metallurgical Engineering and Processing Technology (JMEPT)



Department of Metallurgical Engineering, UPN "Veteran" Yogyakarta
Metallurgical Research and Development Centre (MRDC)-UPNVY
Gd. Urip Sumohardjo Lt. 2
Jl. Babarsari No. 2, Tambakbayan, Yogyakarta 55281


View My Stats