EVALUATING CUTTING TRANSPORT ON 12 ¼” SECTION WELL TM-1
Abstract
Mud hydraulics on a 12-1/4" section needs to be planned properly. Mud hydraulics design on a 12-1/4" section includes determining mud density, flow type, pressure loss, pump specifications, bit hydraulics and cutting lifting design. The purpose of bit hydraulics design is to determine the optimum flow rate. Mud hydraulics optimization is carried out using methods the Bit Hydraulic Horse Power (BHHP), Bit Hydraulic Impact (BHI) and Jet Velocity (JV) methods, where the analysis is in the form of graphs. The graph is analyzed by using a trial and error method to obtain the recommended flow rate so as to provide good cutting lifting. where the expected recommendation analysis are Cutting Transport Ratio (Ft) > 90%, Cutting Concentration (Ca) < 5%, and Carrying Capacity Index (CCI) > 1. The analysis results from the graph show that for the hole 12-1/4", it is recommended to use an optimum flow rate of 626.6 gpm with minimum value of Ft is 90.01%, Ca is 0.87% and CCI is 1.95. These values are stated to be good by using 15-15-16 nozzle bit combination. The Flowrate value can be increased up to 785 gpm by using 18-18-20 nozzle bit combination.
.
Keywords: Hydraulic Mud Planning, Optimum Flow Rate, Cuttings Removal.
Full Text:
PDFReferences
Adam, N. J., & Charrier, T. (1985). Drilling Engineering, A Complete Well Planning Approach.
Al Rubaii, M. M. (2018). A new robust approach for hole cleaning to improve rate of penetration. Society of Petroleum Engineers - SPE Kingdom of Saudi Arabia Annual Technical Symposium and Exhibition 2018, SATS 2018, April 2018. https://doi.org/10.2118/192223-ms
Baker Hughes. (2006). Drilling Fluids Reference Manual. Reference Manual, 1– 775.
Bieler, R. (1990). Selecting a Drilling Fluid. July, 832–834.
Bourgoyne, J. A. T., Keith, K. M., Martin, E. C., & F.S., Y. J. (1986). Applied Drilling Engineering SPE (p. 500). https://store.spe.org/Applied-Drilling- Engineering-Digital-Edition-P576.aspx
Busahmin, B., Saeid, N. H., Alusta, G., & Zahran, E. S. M. M. (2017). Review on hole cleaning for horizontal wells. ARPN Journal of Engineering and Applied Sciences, 12(16), 4697–4708.
Busahmin, B., Saeid, N. H., Hasanah, U., Hj, B., & Alusta, G. (2017). Analysis of Hole Cleaning for a Vertical Well. 4. https://doi.org/10.4236/oalib.1103579
Caenn, R., & Chillingar, G. V. (1996). Drilling fluids: State of the art. Journal of Petroleum Science and Engineering, 14(3–4), 221–230. https://doi.org/10.1016/0920-4105(95)00051-8
Dr. Ir. Rudi Rubiandini R.S., I. (2009). Teknik Pemboran 1. 417–444.
Exlog. (1985). Theory and Application of Drilling Fluid Hydraulics (Vol. 4, Issue 1).
Guo, B., & Liu, G. (2011). Applied drilling circulation systems: Hydraulics, calculations and models. In Applied Drilling Circulation Systems: Hydraulics, Calculations and Models. https://doi.org/10.1016/C2009-0-30657-1
Herianto. (2021). Optimization Rate of Penetration in Directional Drilling with Adjustable Bit Rotating and Hydraulic Hole Cleaning. 9(5). https://doi.org/10.14738/aivp.95.11097
Herianto, & Subiatmono, P. (2021). Teori dan Aplikasi Pemboran Berarah Pada Sumur Minyak dan Gas.
Julikah, J., Rahmat, G., & Wiranatanegara, M. B. (2021). Subsurface Geological Evaluation of the Central Sumatra Basin in Relation to the Presence of Heavy Oil. Scientific Contributions Oil and Gas, 44(1), 65–81. https://doi.org/10.29017/scog.44.1.491
Mahmoud, H., Hamza, A., Nasser, M. S., Hussein, I. A., Ahmed, R., & Karami, H. (2020). Hole cleaning and drilling fluid sweeps in horizontal and deviated wells: Comprehensive review. Journal of Petroleum Science and Engineering, 186, 106748. https://doi.org/10.1016/j.petrol.2019.106748
Okon, A. N., Agwu, O. E., & Udoh, F. D. (2015). Evaluation of the cuttings carrying capacity of a formulated synthetic-based drilling mud. Society of Petroleum Engineers - SPE Nigeria Annual International Conference and Exhibition, NAICE 2015, September. https://doi.org/10.2118/178263-ms
Rabia, H. (2002). Well Engineering & Construction Hussain Rabia. 1 to 789. Subraja, T., Lestari, L., Husla, R., Apriandi, R. R. W., & Yasmaniar, G. (2022).
Analisa Pengangkatan Cutting Menggunakan Metode CCI,CTR, Dan CCA Pada Sumur T Trayek 17 1/2". XI(1), 6–11.
Texaco, C. (2002). The Chevron Texaco and BP Drilling Fluid Manual.
Wastu, A. R. R., Hamid, A., & Samsol, S. (2019). The effect of drilling mud on hole cleaning in oil and gas industry. Journal of Physics: Conference Series, 1402(2). https://doi.org/10.1088/1742-6596/1402/2/022054.
DOI: https://doi.org/10.31315/jpgt.v5i1.10742
This work is licensed under a Creative Commons Attribution 4.0 International License.